Lower Your Tesla Model Y Without Sacrificing Ride Quality: Factory-Tuned Damping and Stainless Construction
The KW 10287010 V1 Coilover Kit delivers precision-engineered height adjustability specifically developed for the 2020 and later Tesla Model Y AWD. Unlike generic coilover kits adapted from similar platforms, KW 10287010 was engineered exclusively for the Model Y’s EV-specific mass distribution, weight bias, and suspension geometry. KW engineers validated every aspect of the 10287010’s spring rates and damper tuning at the Nurburgring Nordschleife and in KW’s proprietary 7-post chassis dynamics test center, ensuring a balanced, daily-drivable performance character.
The INOX-LINE stainless steel construction of KW 10287010 resists corrosion even in harsh winter environments. Every component, from the shock bodies to the adjustment collars, is produced in-house at KW’s facility in Fichtenberg, Germany, using KW-exclusive restricted-chemistry steel and proprietary damper technology. You will not find mass-produced or third-party components in any 10287010 kit.
Ride Height Adjustment
The 10287010 allows a lowering range of 1.0 to 2.0 inches (25 to 50 mm) at both front and rear axles. Front axle adjustment is performed via KW’s threaded strut housings. Rear axle adjustment uses height-adjustable spring perches over the rear dampers. The dirt-resistant trapezoid thread and composite polyamide adjustment collar make height changes fast and precise, even after years of daily use, without requiring special tools beyond the included KW toolkit.
Damper Technology
KW 10287010 features a vehicle-specific, factory pre-set damper valving calibrated for the Model Y AWD’s weight and performance envelope. The damper characteristic curve remains sport-oriented even at full passenger and cargo load, operating within the TUV-tested adjustment range throughout. Body roll is reduced during compression, delivering more direct turn-in and confident cornering without the harshness of aftermarket race-oriented setups.
What’s Included
- 2 front coilover strut assemblies (threaded housing, pre-assembled)
- 2 rear spring and damper assemblies with height adjustment
- Corrosion-resistant springs, bump stops, and all mounting hardware
- KW Toolkit for height adjustment
- Installation and adjustment manual
Specifications
| Attribute | Detail |
|---|---|
| MPN | 10287010 |
| UPC | 4251778316046 |
| Brand | KW Suspensions |
| Series | V1 INOX-LINE |
| Construction | Stainless Steel (INOX-LINE) |
| Lowering Range (Front) | 1.0 to 2.0 in (25 to 50 mm) |
| Lowering Range (Rear) | 1.0 to 2.0 in (25 to 50 mm) |
| Front Adjustment Type | Threaded strut housing |
| Rear Adjustment Type | Height-adjustable spring perch over damper |
| Damping Adjustment | Factory pre-set (not externally adjustable) |
| Max Front Axle Load | 1,363 kg |
| Max Rear Axle Load | 1,500 kg |
| Country of Manufacture | Germany |
| Shipping Weight | 37.3 lbs |
| Shipping Dimensions | 18.0 in W x 6.0 in H x 30.0 in L |
| Approval | TUV part approval (§19.3) |
| Not Compatible With | Vehicles with electronic/active damping systems |
Vehicle Fitment
| Year | Make | Model | Submodel | Notes |
|---|---|---|---|---|
| 2020 | Tesla | Model Y | Long Range | AWD |
| 2021 | Tesla | Model Y | Long Range | AWD |
| 2022 | Tesla | Model Y | Long Range | AWD |
| 2023 | Tesla | Model Y | Long Range | AWD |
| 2024 | Tesla | Model Y | Long Range | AWD |
| 2025 | Tesla | Model Y | Long Range | AWD |
| 2020 | Tesla | Model Y | Performance | AWD |
| 2021 | Tesla | Model Y | Performance | AWD |
| 2022 | Tesla | Model Y | Performance | AWD |
| 2023 | Tesla | Model Y | Performance | AWD |
| 2024 | Tesla | Model Y | Performance | AWD |
| 2025 | Tesla | Model Y | Performance | AWD |
Frequently Asked Questions
Does KW 10287010 work with my Model Y’s air suspension?
No. The 10287010 is not compatible with vehicles equipped with electronic or active damping systems. Verify your trim’s factory suspension type before ordering.
Will installing 10287010 void my Tesla warranty?
Modifying suspension components may affect the coverage of related systems. Consult your service agreement and your Tesla service center before installation.
Is an alignment required after installing 10287010?
Yes. A professional four-wheel alignment is required immediately after installation and again after any subsequent ride height adjustments.
Can I adjust the damping stiffness on 10287010?
The 10287010 features a factory pre-set, vehicle-specific damper tune. Damping is not externally adjustable – this is by design to optimize daily driveability for the Model Y AWD.
How low can I go with 10287010?
The TUV-certified adjustment range allows 25 to 50 mm (approximately 1.0 to 2.0 in) of lowering front and rear, ensuring adequate suspension travel and proper geometry throughout the range.
How long does installation take for an experienced shop?
Most professional shops complete the 10287010 installation in 3 to 5 hours, depending on vehicle condition and whether a same-day alignment is performed.
Is the 10287010 backed by a warranty?
KW coilovers are manufactured to strict quality standards in Germany. Contact KW directly or your authorized dealer for current warranty terms applicable to your region.
What tools do I need beyond the included KW Toolkit?
Standard metric socket and wrench sets, a spring compressor if needed for disassembly, a torque wrench, and access to a professional alignment rack are required.
Does the 10287010 include bump stops and dust boots?
Yes, the kit includes corrosion-resistant springs, bump stops, and all mounting hardware needed for complete installation on both axles.
Installation Instructions
- Safely lift the vehicle and remove all four wheels.
- Disconnect any suspension components attached to the factory strut at each corner (sway bar end links, brake lines, ABS wiring).
- Remove the factory strut assemblies front and rear, taking note of orientation.
- Install the 10287010 front coilover assemblies in place of the factory struts, torquing all fasteners to factory spec.
- Install the 10287010 rear assemblies, seating the spring perches and confirming height adjuster position.
- Set initial ride height per the 10287010 instruction sheet before torquing final fasteners.
- Reinstall wheels, lower the vehicle, and perform a four-wheel alignment before driving.
- After 500 miles of break-in, recheck all fastener torque values and re-verify ride height.
Proposition 65 Warning
WARNING: This product can expose you to chemicals including lead and lead compounds, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Reviews
There are no reviews yet.